Last Updated on February 16, 2023
Table of Contents:
- Preparation
- Disconnecting the Old Shower
- Installing the New Shower
- Testing & Finishing Up
- FAQs in Relation to How to Replace an Electric Shower
- Conclusion
Preparation
Before learning how to replace an electric shower, it is important to make sure you have all the necessary tools and materials. To begin with, you will need a screwdriver, pliers and a new shower unit. You may also require some additional items such as screws, washers or sealant depending on your existing setup.
It is also essential that you turn off the electricity supply before starting any work. This can be done by switching off the circuit breaker at your fuse box or disconnecting the plug from the wall socket if applicable. If in doubt about how to do this safely then please consult a qualified electrician for advice first.
You should also take time to familiarise yourself with how your current shower works so that when it comes time to install the new one you are aware of what needs doing and where each part goes. It might be useful to draw up a diagram of your old system so that when installing the new one everything lines up correctly and there are no surprises later down the line.
Finally, ensure that all surfaces around where you will be working are clean and dry before beginning any installation process; this includes both inside and outside of your bathroom/shower cubicle area as well. This way, any dirt or debris won’t get into any parts which could cause problems further down the line once everything has been put back together again.
Before beginning the installation process, it is important to make sure you have all the necessary tools and materials ready. Now that we are prepared, let’s move on to disconnecting the old shower.
Disconnecting the Old Shower
Turning Off the Power Supply
When it comes to disconnecting an old shower, safety should always be your first priority. Before you start any work on the shower, make sure that you turn off the power supply at the mains. This will prevent any shocks or electrocution when working with wires and cables in close proximity to water. It is also a good idea to double check that all power has been switched off before beginning work.
Draining Any Remaining Water
Once you have ensured that there is no electricity running through the system, it’s time to drain any remaining water from the pipes connected to your old shower. To do this, locate and open up both hot and cold valves near where they connect into your existing plumbing setup. If necessary, use a wrench or pliers to loosen them if they are stuck closed due to rust or other build-up over time. Once opened, allow all of the water left in those pipes out until only air remains coming out of them; this ensures that no further damage can occur during installation of your new shower unit as well as prevents flooding from occurring later down the line.
Once the old shower is disconnected, you can move on to installing the new one – a straightforward process that we will be discussing in the next section.
Installing the New Shower
Installing a new electric shower is an easy task that can be done in no time. Here’s what you need to do:
1. Turn off the power supply to the existing shower and disconnect it from both water and electricity supplies. Make sure all connections are completely disconnected before proceeding further.
2. Take measurements of your bathroom walls, floor, and ceiling to determine where you will install the new electric shower unit. If necessary, use a stud finder or other tools to locate any pipes or wiring behind the wall where you plan on installing the unit so as not to damage them during installation process.
3. Place the mounting bracket for your new electric shower onto the wall at desired height using screws provided with your kit (or appropriate anchors if needed). Once secured into place, connect one end of flexible hose supplied with your kit into back of electric shower unit and other end into main water supply pipe located near by (if applicable).
4 . Connect electrical cables from mains supply into back of electric shower unit ensuring they are correctly connected according to manufacturer’s instructions (consult user manual for more details). Securely fasten cover plate over electrical connection box once finished connecting wires/cables together inside box – this will help protect against moisture getting inside connection box which could cause short circuit or fire hazard later down line if left uncovered/exposed.
5 . Now turn on power switch located outside bathroom door (or wherever else designated) – check that lights up indicating power has been successfully connected before proceeding further.
Finally, test out the newly installed electric shower by turning the knob clockwise until hot water starts flowing out. Adjust the temperature accordingly until a desired setting is achieved and then enjoy warm, relaxing showers every day without worrying about running out of cold water anytime soon.
Once the new shower is securely mounted, it’s time to move on to testing and finishing up.
Testing & Finishing Up
It’s important to test that everything is working correctly before you finish up your home and garden project. Start by testing all the electrical components, such as lights, switches, outlets, etc., to make sure they are functioning properly. Then check for any leaks in plumbing fixtures or pipes. If you find any leaks, repair them immediately.
Next, inspect the work area for any debris or leftover materials that need to be cleaned up and disposed of responsibly. Make sure all tools are put away and the workspace is tidy before leaving it behind. Finally, double-check that all safety measures have been taken care of – turn off power sources when necessary and use caution when handling sharp objects like saws or drills.
Once everything has been tested and checked over thoroughly, it’s time to clean up after installation. Sweep up dust particles from sanding wood surfaces or sawing metal pieces with a vacuum cleaner if possible; otherwise a broom should do just fine too. Wipe down countertops with a damp cloth if needed; this will help remove dirt residue left behind from construction activities like drilling holes into walls or laying tiles on floors. Dispose of any waste materials according to local regulations – some items may require special disposal methods due to hazardous chemicals present in them (such as paint cans).
Finally, take some time to appreciate your hard work. You have successfully completed another home improvement project – congratulations.
FAQs in Relation to How to Replace an Electric Shower
Can I replace an electric shower myself?
Yes, it is possible to replace an electric shower yourself. However, it is a complex task that requires knowledge of plumbing and electrical systems. It’s important to turn off the power before attempting any work on the shower. Make sure you have all the necessary tools and materials before starting. If in doubt, consult a qualified professional for help with installation or repair.
Do I need an electrician to remove an electric shower?
No, you do not need an electrician to remove an electric shower. However, it is important to take the necessary safety precautions before attempting this task. Turn off the power supply at the mains and ensure that all electrical connections are disconnected before starting work. It is also recommended to consult a qualified professional if you are unsure of how to safely disconnect or remove any components from your shower unit.
How long does it take to replace an electric shower?
Replacing an electric shower is a relatively straightforward job that can be completed in 1-2 hours. First, you’ll need to turn off the power and water supply to the existing shower before disconnecting it from the wall. Then, you’ll need to fit any necessary plumbing components such as valves or elbows before connecting your new electric shower unit. Finally, once all connections are secure, you can switch on the power and water supplies and test out your new electric shower.
How do you remove an electric shower?
Removing an electric shower can be a tricky task, but it is possible with the right tools and safety precautions. Firstly, turn off the electricity to the shower at your fuse box or circuit breaker. Then, disconnect any pipes connected to the unit before unscrewing and removing it from its wall mountings. Finally, you may need to detach any wiring from behind the unit before disposing of it safely. Remember that if in doubt about any step of this process then you should seek professional help for assistance.
Conclusion
Congratulations! You have now successfully replaced your electric shower. With a few simple steps, you can upgrade your bathroom with ease and save money in the process. Replacing an electric shower may seem daunting at first, but as long as you follow these steps carefully, it’s not too difficult to do. Now that you’ve finished replacing your electric shower, sit back and enjoy the new look of your bathroom!
Paul is the type of person who never met a problem he couldn’t fix. He can always be found tinkering with something in his house, even if it isn’t broken! His tips and tricks are often shared on our site. He’s the one you call when something breaks because he has been known to improvise fixes for everything from leaky faucets to malfunctioning dryers.